HELIX FPV FRAME

Please note, if you choose to run the stretch center main plates you will need 6" arms to run 5" props.

The Helix Frame was designed in together with the electronics, we highly recommend purchasing the custom PDB and FC board for the best experience. You can of course use your own flight controller, others have done very successfully, but that is a DIY project and not directly supported.

You may choose to use our VTX and OSD board or instead buy the carbon blank replacement plate and use any other VTX you choose.

INTRODUCTION

The Helix is a new breed of FPV quadcopter which integrates the design process of both the air frame and the flight electronics.

By keeping an obsessive focus on enthusiast level performance, but freeing ourselves from the need to support the vast array of third party electronics, we have created a package which offers a unique blend of performance, durability, features, ease and versatility.

LINKS

Helix Minisite

VTX/OSD Downloads

RCGroups community thread

Frequently Asked Questions

SPECIFICATIONS

Helix Frame -

Fully chamfered, high quality carbon fiber frame
Grade 12.9 high tensile alloy steel and 7075 black anodised aluminium hardware
30, 45 and 60 degree FPV camera plates
45 degree HD camera plates
Custom machined antenna clamps
Injection molded ESC fairings
High grade natural rubber Lipo pad
Self adhesive foam-rubber isolation pad for the flight controller
Set of diamond files
Nylon 6 antenna tubes
45 degree SMA adapter

Flight Controller -

Integrated high current PDB
STM32F3 based flight controller
SPI based low noise MPU6000 gyro
Up to 40V input BEC - 6S capable, no extra filtering
PPM, SBUS, Spektrum, Serial rx receiver input
Filtered RSSI input
Hardware UART telemetry output
128Mbit Blackbox flash
Reinforced USB connector
Dual mirrored LED strip outputs
Tactile boot button
Integrated voltage monitoring

Video Transmitter -

Integrated OSD
Integrated microphone
40 Channels
25/200/500mW switchable output power
Power and channels selectable via OSD
Cascaded switching and linear regulators for ultra clean power
Rock solid 5V camera output
Hardware jumper for removing power to module

Electronics Extras -

Dual programmable RGB LED strips
USB to Serial adapter for flashing OSD
Custom cables

REQUIRED

FPV camera - HS1177 (top connector) or Runcam Swift/Owl
RC receiver - No larger than FrSky X4R-SB
FPV antenna - TBS Triumph - SMA
Motors - 2204-2206 class motors to suit prop size with at least one pair of 19mm mounting holes to suit fairings (fairings optional).
ESCs - smaller than 30mm x 15mm x 4.5mm

Standard build tools and supplies, such as silicon wire, XT-60, heat-shrink etc. will also be necessary to complete the kit.

FEATURES

The Helix is compact, the center measures 34mm across and the gap between the two electronics tiers is 10mm. The FPV camera is held at a set angle by carbon plates which follow the contours of the camera to offer full protection with the minimum size and weight. The ZX5 is 200mm motor to motor and the carbon weighs 58g, the ZX6 is 230mm motor to motor and the carbon weighs 62g. Camera plates supporting 30, 45 and 60 degrees are included in every kit.

The Helix is durable, using a 2.5mm base plate and a 2mm top plate, along with the proven strength of the Warpquad arm profile in 4mm carbon. Where it's most needed in the center section we use grade 12.9 high tensile alloy steel, elsewhere to save weight all hardware is 7075 aluminium. Durability is comparable to our Alien frames.

The Helix is easy, building the kit is simpler and more streamlined than any other frame in this class. The ESCs, Lipo, buzzer, LED strips and RC receiver all connect directly to the flight controller. The FPV camera and antenna connect directly to the VTX. The flight controller and VTX are connected by one cable for power and one for serial data.

The Helix is polished, all carbon plates are chamfered, injection molded fairings protect your ESCs from prop strikes, custom machined aluminium clamps keep antennas secure and in the optimal position.

The Helix is precise, the flight controller is fully soft mounted, enlarged holes allow the standoffs to pass completely through to the carbon below leaving the PCB floating on a self-adhesive die cut foam rubber gasket. Isolating the flight electronics from vibrations gives the most crisp and responsive flight characteristics possible.

GOPRO MOUNTING

The Helix is just as comfortable tearing up the track as it is bouncing off trees in a park. To be truly versatile we wanted to mount a GoPro without compromising.

Moving the FPV camera forward and dropping it over the front of the VTX, our dedicated HD camera plates position the GoPro at 45 degrees of tilt and perfectly in the center. By keeping the weight of the camera as low as possible, handling characteristics and performance are maintained at the highest level. Our HD camera plates are included in the kit by default.

ELECTRONICS

The Helix is advanced, the combined PDB and flight controller offers Betaflight support on an STM32 F3 with a SPI based MPU6000 gyro. Blackbox support, direct Lipo input, LED strip outputs and a front mounted buzzer are included. The VTX is combined with an OSD and microphone as well as a rock solid 5V output for your camera. Changing between all 40 channels, as well as 25mw, 200mw and 500mw output power, is all available via menus in the OSD. LED strips and an external USB to serial adapter for flashing the OSD are all provided.

The Helix is powerful, 6S batteries are fully supported. All of the electronics provided are rated to 40V input to cope with extreme voltage spikes from high end motors and ESCs. No extra filtering or special requirements, just obscene power right out of the box.

The Helix is clean, on the VTX we used cascaded switching and linear regulators with additional filtering components. The image is crystal clear under even the most aggressive 6S flying, motor noise in your video feed is a thing of the past. The through-hole SMA connector is a tested and proven design, adding strain relief to the antenna translates any levering forces in to pulling forces where the connector is at its strongest.

The Helix is ready, the required cables between the flight controller and VTX are included, all electronics come flashed and ready to run with sensible defaults.

BUILD VIDEO

A very big THANKS to BMSWEB for this brilliant build video!

Alien 4" K-Mount CF 1.5mm (2 Pack)

Spare Alien 4" K-Mounts - 2 Pack

Related Items

Subscribe